Bike Tail Light with Turn Signals - Ultra Bright Bike Rear Light, Wireless Remote Control USB Rechargeable Bicycle Taillight, Safety Warning Bike Brake Lights and Flashing Lights, Easy Installation

squibomb

$ 39.64




Share this product



    ULTRA-BRIGHT LED BIKE TAIL LIGHT - squibomb bike tail light with turn signal has 29 of 85LM LED lights, bright enough to be seen from 150ft away in foggy/rainy day or even in dark night. USB charging directly(for light+remote control), environment friendly.
    WIRELESS REMOTE CONTROL - Remote control the bike tail light to send signals in different modes by the 5 easy to use buttons on the wireless controller. Remote control on handlebar, easy for cyclist to control during riding. Suitable for Mountain, MTB and Road Bicycles.
    IPX4 WATERPROOF - IPX4 Waterproof level make this bike turning light can be used in small to moderate rain in the temperature of in -4-140F -- your best partner for outdoor biking. Cycling Safety Mountain Bike.
    USB Rechargeable - The bike turn signals use 2200mAh Li-on battery, allow the bike tail light to be fully charge in 3-4 hours and can work for about 7 hours under constant brightness. The remote control use 180mAh Li-on battery, which can keep working for more than 2 months after 1-2 hours fully charge. Both the signal light and remote control can be charged from any USB Port, convenient and save your money and hassle.
    Easy to Install - Take out the turn signal and the fixed support in the packing box, along the grooves, slide the fixed support in grooves and snap the buckle. Put the loaded turn signal on the bicycle seat tube and tighten it with screws, suitable seat tube:0.98-1.26in dia. The remote control is fixed on the bike handle and tighten it up with a screwdriver, suitable handle bar:0.71-1.1in dia.

    Product Dimensions: 4.4 x 1.3 x 1.2 inches ; 3.2 ounces
    Shipping Weight: 10.4 ounces
    Item model number: .
    Batteries 1 Lithium Polymer batteries required.
    #89 in Bike Taillights

Installation Instruction: Remote Control Pairing: At the same time, press the power button of the remote control and turn signal, when the turn signal flickers three times in red, it means the pairing is successful. Turn Signal Installation: 1.Take out the turn signal and the fixed support in the packing box, along the grooves, slide the fixed support in grooves and snap the buckle. 2.put the loaded turn signal on the bicycle seat tube and tighten it with screws. If it is too loose, you’d better to add a rubber gasket. (the turn signal is suitable for the seat tube size: 25-32mm). Remote Control Installation: Take out the remote control and then install it on the bicycle handle, tighten it up with a screwdriver. The remote control is suitable for the handle size: 18-28mm. Product specifications: Dimensions (W x H x D): 111.63033.8mm Weight: 125g Waterproof Grade: IPX4Power Supply : DC 5V 1A Red Warning Light Luminance: 85 lumen Battery Capacity: 2200mAh(bike tail light)/180mAh(remote control). Endurance Time: Work for about 7 hours under constant brightness Charging Time: The charging time is about 2-3 hours.Product Included: Intelligent Turn Signal1 Remote Control1Turn Signal Fixed Support1 Rubber Gasket2 Micro USB Charging Cable1Fixed Screw and Nut for Turn Signal1 M4 20mmScrew and Nut for Remote Control1 M5 25mmUser Manual1Warranty:1. When the remote is paired with the turn signal, you must wait for the red light to flash three times. Otherwise, it will not be paired and the control distance will be short. 2. Please charge the lights in time before the batteries run out,or it will damage the batteries. 3. Use the USB cable comes with the light to charge, don't use other cables to charge, otherwise it's easy to damage the device.